Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
Just how do you really feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily available, the task can move rapidly; if you need to open a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the task and also fit attempting it. Instead of employing a service provider to take control of a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your washroom if you have already purchased a new tub as well as do not require to alter the setup of your previous water pipelines.
Your devices and also product checklist should comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, place the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and also check all joints as well as new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Finally, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bathtub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the tap and the sink. Secure the tap in position with the supplier given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about Installing A Bathtub? Leave a review down below. We would be pleased to see your opinions about this blog posting. We hope that you come back again in the future. Loved our review? Please share it. Let others locate it. I praise you for your time. Come back soon.
Schedule Report this page